Digiplex DGP-641 Manuel d'installation télécharger pdf (Page 32)

28 Reference & Installation Manual

If the control panel still fails to report to a monitoring station

telephone number after reaching the Maximum Dialing Attempts

(see section 8.6.1), the control panel will dial the selected backup

telephone number unless the Alternate Backup Option is enabled

(see section 8.6.3). When the Alternate Backup Option is enabled,

the control panel will dial the backup number after every failed

attempt.

8.6.1 Maximum Dialing Attempts

SECTION [257]

The number (001 to 255) programmed into section [257]

determines how many times the control panel will dial the same

monitoring station telephone number before proceeding to the next

number. Also refer to section 8.6.3.

8.6.2 Delay Between Dialing Attempts

SECTION [258]

This delay will determine the amount of time the control panel will

wait between dialing attempts. This delay can be set from 001 to

255 seconds.

8.6.3 Alternate Backup Option

SECTION [522]: OPTION [6]

With option [6] enabled in section [522], the control panel will dial

the selected backup telephone number after every failed attempt to

contact a monitoring station telephone number. Otherwise (option

[6] off), the control panel will only dial the backup telephone

number after the Maximum Dialing Attempts (see section 8.6.1) to

one monitoring station telephone number have failed.

8.7 Recent Close Delay

SECTION [219]

If after having armed the system, an alarm is generated within the

period programmed into section [219] (000 to 255 seconds), the

control panel will transmit the Recent Close report code

programmed into section [679].

8.8 Auto Test Report

SECTIONS [261] AND [270]

The control panel will transmit the test report code programmed

into section [717] after the number of days (000 to 255)

programmed into section [261] has elapsed and at the time (00:00

to 23:59) programmed into section [270].

8.8.1 Hourly Test Transmission

SECTION [522]: OPTION [3]

Alternatively, the control panel can transmit the test report code

programmed into section [717] every hour. Turn off option [3] to

disable this feature. Program the minute of each hour (00:00 to

00:59) it sends the test report into section [270].

8.9 Power Fail Report Delay

SECTION [260]

The control panel will delay transmission of the AC Failure report

code programmed into section [712] by the period programmed

into section [260] (000 to 255 minutes).

8.10 Disarm Reporting Options

SECTIONS [506], [510], [514], [518]: OPTION [7]

Since the control panel can enable the Disarm Reporting Options

for each individual partition, select the section that corresponds to

the desired partition and turn option [7] on or off as desired.

Sections [506], [510], [514], [518] represent partitions 1 to 4

respectively.

Report On Disarm After Alarm Only

Option [7] ON

The Digiplex control panel will send Disarming Report Codes (see

section 8.2.3 on page 25) to the monitoring station only when the

system is disarmed following an alarm.

REPORT ON DISARM

Option [7] OFF

The Digiplex control panel will send the Disarming Report Codes

(see section 8.2.3 on page 25) to the monitoring station whenever

a partition is disarmed.

8.11 Zone Restore Report Options

SECTION [522]: OPTION [8]

Report On Zone Closure

Option [8] ON

The control panel will send the Zone Alarm Restore report codes

(see section 8.2.6 on page 25) to the monitoring station as soon as

the zone returns to normal (zone closure) or upon disarming

Report On Bell Cut-off

Option [8] OFF

The control panel will send the Zone Alarm Restore report codes

(see section 8.2.6 on page 25) to the monitoring station when the

Bell Cut-Off Timer has elapsed or when the alarm has been

disarmed (see section 7.2 on page 22).

8.12 Pager Delay

SECTION [259]

When using the Pager Reporting Format (see section 8.5.5 on

page 27), the control panel will wait for the delay period

programmed into section [259] (001 to 060 seconds) before

uploading the report codes to the pager. This is to allow time for the

pager system to provide a dial tone or to bypass the welcome

message before sending data.

8.13 Auto Report Code Programming

SECTIONS [790] TO [795]

When using either the Contact ID or SIA Reporting Formats (see

section 8.5 on page 27), the Digiplex system can automatically

program a set of default report codes. From programming mode

(see section 3.1 on page 9) enter any of the following sections to

set the indicated report codes:

All Codes

Section [790]

Sets all report codes in sections [600] to [718] with the default

values from the Automatic Report Codes List in the Programming

Guide.

Arming & Disarming Codes

Section [791]

Sets all report codes in sections [600] to [654] with the default

values from the Automatic Report Codes List in the Programming

Guide.

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 67 68

Commentaires sur ces manuels

Pas de commentaire

Digiplex DGP-641 Manuel d'installation Page 32

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Digiplex DGP-641